ZENCUT  |  WINDOWS 7  |  SIGNCUT  |  FLEXI 10  |  ESPAÑOL  




ZENCUT DRIVER AND SETUP GUIDE
FOR WINDOWS 7




WARNING: DO NOT PLUG THE CUTTER VIA USB BEFORE INSTALLING THESE DRIVERS, YOU WILL BE ASKED TO CONNECT THE CUTTER IN LATER STEPS.

STEP 1: Download the cutter driver.


* * * DOWNLOAD ZENCUT GREEN USB DRIVER * * *



* * * * * * * * * * * * * * * * * * * * * * * * * * * *

* * * DOWNLOAD ZENCUT BLACK USB DRIVER * * *



* * * * * * * * * * * * * * * * * * * * * * * * * * * *

STEP 2: Locate the file and double click to install. The following screen will appear for a few seconds.



STEP 3: The USB & Printer Driver Install screen will be displayed, press Next.



NOTE: Installing driver files... Once completed, press Next.



STEP 4: The driver installation is complete. Press Finish.



STEP 5: Connect your ZenCut to the power source and turn on. Load a vinyl roll, measure it to detect the material using the commands on the cutter screen.

  • Choose "roll" to measure the width of the vinyl
  • Choose "edge" to measure the width and return the cutter to the front of the roll
  • Choose "sheet" to measure the width and the length of a single sheet


USB PRINTER TYPE (Windows 32-bit or 64-bit)

IMPORTANT: Before connecting the cutter to your computer, check if the Operating System version is 32-bit or 64-bit as there is a setting in the cutter called “USB Printer Type” that needs to be adjusted accordingly to your computer’s processor architecture.

STEP 6: The following steps should be performed in the Cutter:

  1. Press the Online / Offline button
  2. Press the Misc button
  3. Press the Left key 3 times and look for USB Printer Type
  4. Press the Enter button to select USB Printer Type
  5. Press the UP or DOWN buttons to select
    Zencut = 32-bit (x86)
    OR
    Common = 64-bit (x64)
  6. Press Enter to make a choice
  7. Press ON/OFF Line twice

STEP 7: Connect the ZenCut to the Computer via USB. Windows will detect and install the driver, give Windows about 2 minutes to do so.



STEP 8: Once the driver has been successfully installed you will see the following screen.



NOTE: After installing the driver, the Device Manager will display a new entry under Universal Serial Bus controllers named USB Printing Support.

STEP 9: Open the Device Manager to ensure the cutter driver has been installed. If not repeat Step 1.

To access Device Manager, use any of the following methods:

  • Start > Run > and type: devmgmt.msc
  • Start > Control Panel > Device Manager or System
  • Start > and do a Search for Device Manager or dev
  • Start > Control Panel > System and Security > System > Device Manager
  • Hold the Windows key + Pause Break > Device Manager
  • Right-click My Computer > Properties > Device Manager




ZENCUT PRINTER

IMPORTANT: Keep in mind that this cutter installs as a Printer and that can found in Printers. Check if this printer is present.

To access the Printers section use the following methods:

  • Start > Printers
  • Start > Control Panel > Printers
  • Start > Run > and type: Control Printers
  • Start > Control Panel > Hardware and Sound > Printers

STEP 10: Locate the ZenCut printer, right click it and select Properties.



STEP 11: Select the Ports tab and ensure that your printer matches the setting in the example below. 




* * * * * * * CUTTING SOFTWARE SETUP AND INSTALLATION * * * * * * *
CLICK THE ICON FOR THE SOFTWARE YOU ARE USING TO CONTINUE SETUP





IMPORTANT: If you have had any problems with this guide and need help or if you would just like to send us feed back on this guide please click the Live Support icon to enter into a chat with our support staff.


Enjoy your new vinyl cutter! Thank you for choosing USCutter